In a September 3rd Tower Hobbies press release, details of the much anticipated Futaba GY701 Gyro and GY701 Governor were revealed. Read on to get the details.
*Note:
A call to Tower Hobbies confirmed In Stock and availability of GY701 Gyro (FUTM0821) only and GY701 Governor (FUTM0820) only as individual components.
The GY701 Gyro/Governor (FUTM0822) combo and GY701 Gyro/Governor combo with BLS251 servo (FUTM0823) are NOT available at this time. Check back with Tower Hobbies for availability of combo stock numbers.
BEGINNER FRIENDLY – COMPETITION READY!
The Futaba GY701 combines a gyro and governor in one unit – a quantum leap forward in technology – with ultra high-speed processing rates that make it the most sophisticated system on the market. Basic and Expert menus make it easy for novices and pros alike to enjoy latency-free performance and virtually instantaneous set-ups. The GY701′s OLED (Organic Light Emitting Display) is easy to read indoors or out. Add the Governor and the system is optimized for even the most extreme helicopter competitions!
- Small and lightweight – only 1.7″ x 1.2″ and weighs less than 1/2 ounce*
*Controller weight only
- S.Bus capable – a single cable connection to the receiver
- Updated firmware and software using CIU-2
- Easy for anyone to program with both Basic and Expert menus
FUTM0822
Gyro/Governor combo
Stock Status: (Estimated) Late September
This is the Futaba GY701 Gyro and Governor.
FEATURES:
GY701 Gyro-
Utilizes MEMS (Micro ElectroMechanical System) technology to ensure ultra high-speed processing
S.Bus capable, a single cable connection to receiver
Internal mixing through S.Bus for no latency or tail offset
Sensor has aluminum alloy case and 2-color mode indicator LED
3D and F3C mode selectable
Governor-
Organic Light Emitting Display (OLED) 128 x 36 dot graphical display for easy outdoor viewing in bright sunlight
Advanced PID control algorithm and consistent pirouette rate and yaw control
Mode selectable for governor or rev limiter
Easy for anyone to program with both Basic and Expert menus
Updatable firmware and software using the CIU-2 PC Interface-not included, order FUTM0951
Compatible with analog or digital servos
INCLUDES:
Futaba GY701 Governor with Instruction Manual, three Sensor Mounting Stays, Adjustment Screwdriver, Governor Sensor, Red and Black Extensions, two Magnets, Sensor, TX and Governor Labels, GY701 Gyro
REQUIRES:
Installing in heli, connecting to receiver and mounting magnets and sensor
SPECS:
Gyro-
Size: 0.83 x 0.83 x 0.31″ (21 x 21 x 8mm)
Weight: 0.33oz (9.4g)
Operation Range: +/- 1,200 deg/sec
Supported Servo Types: Digital 1520µS
Digital 760µS
Governor-
RPM Range: 1,000 – 3,000 RPM
Length: 1.73″ (44mm)
Width: 1.14″ (29mm)
Height: 0.47″ (12mm)
Weight: 0.459oz (13g)
Maximum Operating Voltage: 3.8 – 8.4V DC
Current Drain: 80mA
Selectable Servo Frame: 70Hz, 280Hz and 570Hz (gyro only) rate
Flight Mode: User selectable F3C or 3D (gyro)
Center Pulse Width: 1520µS (70Hz and 280Hz frame rate)
Control Resolution: 0.1Hz (6RPM) engine speed
Speed Stability Accuracy: 1%
Speed Control Range: 1,000 – 3,000 RPM rotor speed
Operating Temperature: 14° – 113°F (-10° – 45°C)
Control System: Digital Advanced Control
Sensor: Vibrating structure gyro/magnetic sensor (gyro/governor)
Angular Velocity Range: +-1,200° per second
Also being offered as:
FUTM0821
GY701 Gyro only
Stock Status: In Stock
FEATURES:
Utilizes MEMS (Micro ElectroMechanical System) technology to ensure ultra high-speed processing, advanced PID control algorithm and consistent pirouette rate and yaw control
S.Bus capable, a single cable connection to receiver
Internal mixing through S.Bus for no latency or tail offset
Sensor has aluminum alloy case and 2-color mode indicator LED
INCLUDES:
Futaba GY701 Gyro with instruction sheet
FUTM0820
GY701 Governor only
Stock Status: In Stock
FEATURES:
Organic Light Emitting Display (OLED) 128 x 36 dot graphical display for easy outdoor viewing in bright sunlight
Advanced PID control algorithm and consistent pirouette rate and yaw control
Mode selectable for governor or rev limiter
Easy for anyone to program with both Basic and Expert menus
Updatable firmware and software using the CIU-2 PC Interface-not included, order FUTM0951
Compatible with analog or digital servos
One year limited warranty through Hobby Services beginning at date of purchase
INCLUDES:
Futaba GY701 Governor with Instruction Manual, three Sensor Mounting Stays, Adjustment Screwdriver, Governor Sensor, Red and Black Extensions, two Magnets, Sensor, TX and Governor Labels
REQUIRES:
Installing in model, connecting to receiver and mounting magnets and sensor
SPECS:
RPM Range: 1,000 – 3,000 RPM
Length: 1.73″ (44mm)
Width: 1.14″ (29mm)
Height: 0.47″ (12mm)
Weight: 0.459oz (13g)
Maximum Operating Voltage: 3.8 – 8.4V DC
Current Drain: 80mA
Selectable Servo Frame: 70Hz, 280Hz and 570Hz (gyro only) rate
Flight Mode: User selectable F3C or 3D (gyro)
Control Resolution: 0.1Hz (6RPM) engine speed
Speed Stability Accuracy: 1%
Speed Control Range: 1,000 – 3,000 RPM rotor speed
Operating Temperature: 14° – 113°F (-10° – 45°C)
Control System: Digital Advanced Control
Sensor: Vibrating structure gyro/magnetic sensor (gyro/governor)
Angular Velocity Range: +-1,200° per second
FUTM0823
GY701 Gyro/Governor combo with BLS251 brushless tail rudder servo
Stock Status: (Estimated) Late October
Source: Tower Hobbies
Got mine today and im in Australia, this thing rocks + TORQ servo with unregulated 2s LIPOs