Safe Switch 2
Price: $35.00
Model: prr-rmtsw2

1 Safe Switch 2

NEW VERSION NOW AVAILABLE

Just the same as the Safe Switch, but instead of a Deans Compatible Connector for the output, the Safe Switch 2 comes with 2 Male to Male Servo Connectors to connect to your Rx.

The Remote Switch is designed for inputs of 2s – 3s packs and capable of delivering 20A, which can be used for any sized Helicopter as well as large Airplanes. Simply run inline between your rx battery pack and its intended item (rx, voltage regulator, etc) and remotely mount the switch in an easily accessible area and your good to go. A bright red led mounted on the unit will give visual verification of power status.

You can use our Remote Switch several different ways. Use the actuator on the side of the board to turn the unit on and off, turn the switch to the on position and use your Spektrum Bind-Plug on the pins. With the plug inserted on the pins, the unit is off, pull the Plug off and the unit turns on. Have an old “Pin Flag” setup? Simply replace the female lead to a male lead and it too can be used to turn the unit on and off.

Our Remote Switch is a “fail-safe” design that fails in the on position and is 100% compatible with our full line of Voltage Regulators. Unit comes wrapped in clear pvc heatshrink and double-sided tape on the rear.

Unit comes packaged with 2 x 6″ Male to Male, 22AWG Servo Connectors to connect to your Rx.

Min. Input Voltage: 2s – 7.4v / A123/Life-6.6v
Max. Input Voltage: 3s – 11.1v
Current Capacity: 20A
Length of Battery Lead Plug: 4″
Length of Rx Lead Plugs: 6″
Plug Type: Deans Compatible
Size: 32mm x 18mm x 6mm
Line Break - Medium Green
Rigid V2
Price: $40.00
Model: prr-6vdns

1 Rigid V2

NEW VERSION 2 NOW AVAILABLE

We have re-designed our popular 6v Regulator. Moving the Power Switch to the end of the unit and raising the Secondary Voltage output from 5v to 5.3v. Installation is simple… Connect your 2s Lipo/Li-Ion Battery, connect the 2 x 6″ Male to Male Servo Connectors into the Rx (Rudder and Gyro Gain Suggested), then connect those specific plugs onto the unit for for Regulated 5.3v.

The Unique design of the Heatsink with ULTRA-THIN Fins allows for super fast dissipation of heat and makes Installation a breeze due to not needing air-flow over the Heatsink.

Also built into the same unit is a 5.3v Regulator for use with Gyro / Tail Servos that are suggested to use an input of 4.8v – 5.3v. This compact and light-weight Voltage Regulator will definatley exceed your expectations!!!

Unit comes packaged with 2 x 6″ Male to Male, 22AWG Servo Connectors to connect to your Rx.

Min. Input Voltage: 7.4v
Suggested Input Voltage: 7.4v
Main Output Voltage: Constant 6v @ 10A
Gyro/Tail Output Voltage: Constant 5.3v @ 3A
Max. Main Amp Rating: 16A
Max. Gyro/Tail Amp Rating: 5A
Heatsink Material: Aluminum
Length of RX Lead Plugs: 6″
Length of Battery Input Lead Plug: 6″
Plug Type: Deans Compatible, Universal
Size: 60mm x 30mm x 9mm
Line Break - Medium Green
Spekline V2
Price: $40.00
Model: prr-spkln

1 Spekline V2

NEW VERSION 2 NOW AVAILABLE

No need to choose between the 6v or 6.5v version anymore. Our new Spekline Voltage Regulator has the ability to select between the 2. With the simple flick of a switch, you can now select the output Voltage to 6v or 6.5v and with the dual colored LED’s, visual indication is easy. Red is 6v and Green is 6.5v, so set it, forget it and GO FLY!!!

Are you using or do you want to use the Spektrum AR7100 or AR7100R Rx, but don’t want to run straight 2s voltage to your cyclic servos? With our new In-Line Voltage Regulator, you can run 6v or 6.5v to that Rx instead of the straight 2s voltage. Another good thing too, the Rx’s internal regulator will still function properly for its own regulated channels.

Regulators are already pre-wired with 16awg silicone wire and Deans Compatible connectors.

The Unique design of the Heatsink with ULTRA-THIN Fins allows for super fast dissipation of heat and makes Installation a breeze due to not needing air-flow over the Heatsink.

This compact and light-weight Voltage Regulator will definatley exceed your expectations!!!

Suggested Input Voltage: 7.4v
Output Voltage: Constant 6v / 6.5v @ 10A
Max. Main Amp Rating: 16A
Heatsink Material: Aluminum
Length of Lead Plugs: 4″ Each
Plug Type: Deans Compatible
Size: 30mm x 30mm x 9mm
Weight: 20g
Line Break - Medium Green
Igniter V2
Price: $45.00
Model: prr-pbglo

1 Igniter V2

NEW VERSION 2 NOW AVAILABLE

We have completely re-designed our popular Igniter. It is now much smaller and works on 4.8v – 10v input. With an On-Board Button (Button Extension Sold Seperately) and dual LED’s to let you know when the unit is activated and when your getting Glow, your sure to know starting your model will be a breeze.

A bright Red LED will come on as soon as you push the Button to indicate the unit is activated and a second Red LED will also light up indicating there is Glow. If the second LED does not come on, then there is no Glow and time to check the Plug or connections.

If unable to mount in a location to reach the On-Board Button, a Button Extension is Available.

Unit comes packaged with a 6″ Male to Male, 22AWG Servo Connector to connect to your Rx and 8″, 18AWG leads for Ground (Ring Terminal) and Glow Plug (Insulated Alligator Clip).

It’s truly a “PLUG-N-FLY” setup…

Min. Input Voltage: 4.8v
Max. Input Voltage: 10v
Output Voltage: 1.25v
Length of RX Lead Plug: 6″
Lenght of Glow Plug Leads: 8″
Plug Type: Universal, Ring Terminal, Clip
Size: 44mm x 16mm x 6mm

You can order directly from the Perfect Regulators website or from your favorite Dealer listed HERE.

Source: Perfect Regulators

Subscribe to the post comments feeds or Leave a trackback