A short interview with Shawn Spiker of Hitec RCD USA (pictured with Dick Rutan).

[ click here to see videos, photos & rest of story ]

If you enjoy our post, feel free to subscribes to our rss feeds

Not only is this Hitec’s first high voltage servo, it’s also thier fastest standard sized servo pushing speeds under 0.06 seconds at 60 degrees! The Hitec HS-7940TH is designed to run directly and safely off a 2s lipo battery pack. With the HFP-20, HPP-20 or HPP-21 servo programmers you will have a variety of options to fine tune the servo to your needs.

[ click here to see videos, photos & rest of story ]

If you enjoy our post, feel free to subscribes to our rss feeds

New 2009 Futaba Products!

On the heels of the 2009 Nuremburg Toy Fair Robbe Austria has published information on Futaba’s new brushless and digital servos and micro 6-channel FASST receiver! Some of these versions are being brought to the USA!
[ click here to see videos, photos & rest of story ]

If you enjoy our post, feel free to subscribes to our rss feeds

Found these interesting photos of some new JR products in the pipeline.  Check out this post.

[ click here to see videos, photos & rest of story ]

If you enjoy our post, feel free to subscribes to our rss feeds

From the Popular JR 8717 now released the new DS8717HV High Voltage Ultra Speed Cyclic Servo.  With a price tag of $199.99.  Check it out.

[ click here to see videos, photos & rest of story ]

If you enjoy our post, feel free to subscribes to our rss feeds

I just, myself, switched to an 8v setup on my Aling T-Rex 700 and I must say there is a world of difference from 5v and 6v systems.  I am running direct from my lipo using the Arizona Fromenco Kiwi.  Surprisingly I AM NOT using 8717′s but I am using Futaba 9452s with NO PROBLEMS.  I am always aware that they could die any second but seems not to be the case, so far.

Hi-Tec has come out with an 7.4v (8v) line of servos that aren’t super great but at least give you confidence they have been tested at 8v without failures.

[ click here to see videos, photos & rest of story ]

If you enjoy our post, feel free to subscribes to our rss feeds

Align is always busy with something! Check out the new metal tail servo mount for your T-Rex heli! Displayed on the mount is the “T-Rex500″ wording, very nice touch Align! Available soon at your local Align distributors.

If you enjoy our post, feel free to subscribes to our rss feeds

If the DX6i was not cheap enough, spektrum has stepped up the game again and has released the Spektrum DX5e! It comes with the radio, an AR500 reciever, and 4 AA batteries, all at a whopping $99 price point.

If you enjoy our post, feel free to subscribes to our rss feeds

A while back, one of the local hobby shops in my area started carrying these Ino-Lab servos from Korea. While they are neither very fast nor really torquey(like those JR 8717 on 7.4v), they are still pretty decent and at the very least, still compares well to the current “decent” digital servos like the Futaba BLS451/BLS252 servos and the Hi-tec 69XX/79XX series. The best part is that it only cost half of what the Futaba BLS series and JR8715/8915, the 8717 for non-US market, are going for.

[ click here to see videos, photos & rest of story ]

If you enjoy our post, feel free to subscribes to our rss feeds

YES! You didn’t read the headline incorrectly. It seems that the only thing R/C that Align hasn’t release is nitro fuel (ok..TX & RX too..). I Hope they get the first release of these servos right.

It was posted on the Taiwan Align Forum. No ETA, no estimated price yet.

Hitec 7975HB- Probably just a rebadged servo…Align might not even rebadge it.

Not sure why, but they look like savox servos to me. The spec seems to be the same too, but I am not certain if they really are, so don’t quote me on that

• Coreless, low consumption motors.
• 12Bit processor
• Metal gears
• Voltage:DC 4.8-6V
• Operating Temp:-20°C to +60°C
• Dimension:40.3 x 20.1 x 36mm
• Weight: 52.2g (No typo here, on the Align forum, the dimension and weight of the DS610 & DS620 are the same) 

[ click here to see videos, photos & rest of story ]

If you enjoy our post, feel free to subscribes to our rss feeds

I saw these servos in a guy’s helicopter here in L.A. and wanted to see what these were all about. Well, at $169.00 (MSRP) a piece I don’t think that I will be buying any anytime soon. Specs are silly fast.

•   Type: Ultra Speed Heli Cyclic Servo
•   Torque: 160 oz/in @ 4.8V; 196 oz/in @ 6V
•   Speed: .09 sec/60° @ 4.8V, .07 sec/60° @ 6V
•   Dimensions (WxLxH): .83″ x 1.59″ x 1.57″
•   Weight: 2.36 oz
•   Gears: Metal

If you enjoy our post, feel free to subscribes to our rss feeds